What is the “bleed” of an IR series precision regulator?
What are the possible causes of air leaking from the small hole in the body of an IR series precision regulator when the supply pressure is 0.5 MPa and the set pressure is 0.2 MPa?
What does the “Sensitivity―(Within 0.2% of full span)” listed in the IR series precision regulator catalog refer to?
Is it possible to panel mount an IR1000/2000/3000 series precision regulator?
Is it possible to install an IR series precision regulator between the cylinder and the solenoid valve?
What is the difference between IR, IR-A, and ARP series precision regulators? Also, what is the difference between the abovementioned precision regulators and IR-A series regulators (IR1200-A, IR2200-A, and IR3200-A)?
Is it possible to modularly connect an IR3000-03-A (or IR3200-03-A) to an AF40-03-A and AFM40-03-A?
Is there an IRV series vacuum regulator with a female thread?
For IRV series vacuum regulators, is it possible to mount a KQ2 series fitting on the part where the gauge is attached?
Can an ITV series electro-pneumatic regulator be installed between the cylinder and the valve for the single-sided multistage pressure control of the cylinder?
What are the possible causes of an ITV series electro-pneumatic regulator making abnormal sounds?
When the LED display of an ITV series electro-pneumatic regulator indicates an error, what are the next steps to be taken? At present, Er. 1 (Error 1) is displayed on an ITV2030-222S electro-pneumatic regulator.
Are there any power cable lengths other than the standard 3 m cable for ITV1000/2000/3000 series electro-pneumatic regulators?
What is the communication cable part number for ITV series CC-Link, DeviceNet, and PROFIBUS DP compatible electro-pneumatic regulators? Also, what is the wiring method and specifications of the cable?
Is there no longer a gauge port just below the digital pressure display on ITV series electro-pneumatic regulators?
In the ITV series electro-pneumatic regulator catalog, it states that the output pressure is temporarily held when the regulator is powered OFF when in a control state. What does this mean?
What is the M5 tapped hole at the bottom left of the digital pressure display on ITV2000/3000 series electro-pneumatic regulators for?
What type of ITV series electro-pneumatic regulator is recommended for outputting only a predetermined amount of pressure?
Is there a regulator that can be used with water?
What is the resolution of ITV2010 electro-pneumatic regulators?
Is there a regulator that can be used with nitrogen gas?
How come after the pressure of an SRH4000 is set, the pressure on the outlet side increases slightly over time?
What is the difference between the relief type and non-relief type exhaust mechanisms of AR series regulators?
What do the “Flow Rate Characteristics” graphs in the SRH series catalog show?
Why is it recommended that 1 preset pressure be set to 0 MPa for ITV series preset input type regulators?
Is it possible to change the type of pressure units or the number of digits displayed on the LEDs of ITV1000/2000/3000 series electro-magnetic regulators?
In the “Standard Specifications” section in the ITV series catalog, why is the 4 to 20 mADC input signal current type not available for the 2-wire type?
Is it possible to view the catalogs of each type of old AR series regulator (2 digits: AR□□, 4 digits: AR□□□□, and 3 digits: AR□□□) in order to replace them with current products?
What is the pressure gauge port size of AR series regulators?
Is it possible to change the pressure gauge port size to mount a different pressure gauge or fitting on an AR10-M5-A (Rc1/16)?
Is it possible to change the pressure gauge to face the opposite side or change a square embedded type pressure gauge to a round type pressure gauge for AR20-B to AR60-B series regulators?
What are the part numbers of AR-A/AR-B/AR-D series regulator round pressure gauges?
What kind of product is the AR□K-B/AR□K-D series regulator with a backflow function?
What are the part numbers of AR-A/AR-B series regulator brackets? Also, is it possible to order only the set nut?
How do I adjust the pressure of an AR series regulator?
The flow rate characteristics listed in the AR series catalog are for when the inlet pressure is 0.7 MPa, but what happens to the flow rate characteristics when the inlet pressure is 0.5 MPa?
What kind of pressure control device is the ITV series electro-pneumatic regulator? Also, how is it operated and what is the operating principle?
Why is it stated in the precautions for the ITV series electro-pneumatic regulator that the power should be turned OFF when the supply pressure is cut?Also, is there anything else that needs to be done?
Is there a troubleshooting guide for ITV series electro-pneumatic regulators? If so, where can it be viewed?
I have questions about the ITV1000/2000/3000 series CC-Link type regulator.① Is there a built-in terminating resistor? ② How is the pressure set? ③ What is the part number of the Bus adapter?
What is the monitor output option for ITV1000/2000/3000 series regulators?
What is the analog output 4 to 20 mADC (sink type) monitor output for ITV1000/2000/3000 series regulators?
What are the part numbers of AR□□ series regulator replacement parts?
What is the responsiveness of ITV1000/2000/3000 series regulators?Also, is there a way to improve the response time?
Is there an oil-free specification ITV series regulator?
How can I determine the output pressure display accuracy value of an ITV1000/2000/3000 series regulator using the formula in the “Specifications” section in the catalog? (±2% F.S.±1 digit or less)For example, what is it for the ITV2030 (pressure range: 0.5 MPa)?
Is it still possible to order old IT200/400/209 or ITV1000/2000/3000 series electro-pneumatic regulators?
What precautions should be taken when replacing an old IT200/400/209 or IT1000/2000/IT4000 series electro-pneumatic regulator with one from the current ITV1000/2000/3000 series?
What are the replacement part numbers for old IR400/IR401/IR402/IR412 series precision regulators?
What are the replacement part numbers for old IR200/IR201/IR202 series precision regulators?
What do the “Relief Flow Rate Characteristics” graphs in the IR series catalog show?
Is it possible to use a VEA series power amplifier for electro-pneumatic proportional valves with a PVQ series compact proportional solenoid valve?